It Still Works
How would I wire them and is it worth a try? Manuel, Your subs probably blew because they were being driven with twice their rated power. With the above mentioned head unit, which setting should I use? You could also wire the voice coils in parallel and the subs in series and produce the same load conditions. If I connect it what will be my outcome.
Stanley, The best way to wire your gear together is like this. This area is probably best left to those who really know what they're doing and have a very expensive system to justify it. The amplifier sees the same load on its outputs and the subwoofers receive the same amount of power.
- The only way to wire that gear together is like this.
- Brand names and model numbers work best.
- What is your suggestion on wiring?
- What's the best way to wire them to get good bass?
It'll under-power the sub, but it should be alright as long as you don't play distortion trying to get more bass out of the system. They are for very minor power problems and simply add a more sophisticated look to an audio system. Just wanted to know if this amp has enough to power these subwoofer without any damage to any of my equipment? How can I best wire this up? And if so, how to calculate the impedance?
Hooking up 2 subs to a single amp
Terrence, If your vehicle's headlights dim a bit on big bass hits, a capacitor might help. That's dependent on how loud an amp plays into its impedance load. John, Although you've identified your amplifier, you haven't identified your subwoofers. Installed in ported box with a output for each speaker. For wiring subwoofers, dating we recommend using wires of to gauge in size.
To accomplish this be prepared to do a lot listening and moving, along with making setting adjustments to get the best result for your room and listening preference. Is this the best and only safe way to run this with a factory amplifier? What would be the best way to wire the subs to get the most out of them. If you do hook your amp up to the one-ohm setup, it will probably overheat or go into protect mode. Can I hook up a much higher or lower wattage subwoofer since its powering itself?
How to Wire 2 Subwoofers on a Mono Amplifier
Which should put out maybe Rms? Mark, Without knowing the model numbers of your subwoofer components, or how they're wired together, I can't tell for sure. Just make sure you set the amp gain so no distortion ever plays. Not knowing exactly what you have makes giving wiring advice difficult. According to the specs, what the most popular free you should be alright.
Just be sure to never play distortion trying to get loud bass. Like everyone else, I want all I can get out of the amp, but I don't want to burn it up. Room and budget aren't problems. For Tech Support, and 50 call Begin chat.
If i get one amp how close can i get to. Make sure you set the amp gain so no distortion ever plays. Determine whether you need multiple batteries and capacitors. Your reply will be sent to Continue where you left off.
Share your experience with Bill Crutchfield. The hands-on experience I get with car stereos while doing video production is an invaluable aid to me in learning about their exciting features. Would this amp be enough power to run this set up or would you have another recommendation?
The right type of amp to use This setup is perfect for a mono sub amp. Zaheer, The number of speakers an amplifier can power at the same time completely depends on what kind of speakers they are, what their impedance is, and what their power ratings are. Im going to wire the speakers parallel. Dual voice coil subs give you more wiring options than single voice coil models. They are rated by Farad's and the higher they are, the better the cap can store and release volts.
Did this article help you? Any help would be much appreciated! If rated under, make sure your amp's level is not too high as you can damage the sub.
The impedance of a subwoofer coil is expressed in ohms. Even a high-output alternator, beefed-up wiring, and a second battery might not be enough to support this monster of a system. Or, you could wire one sub per terminal set, and then run two pairs of wires to the amp, it's electrically the same. But you should be alright as long as you set the amp gain so no distortion ever plays.
How to Connect and Set Up Two or More Subwoofers in your Home Theater
Which is the best way to hook them up to get more bass or do I need a bigger amp? You simply connect your speaker outs from your amp to the speaker in of the sub, then connect the speaker outs of your subs to your speakers. Andre, That amplifier is twice as powerful as what those subs can normally deal with.
Video of the Day
Or you can just use one pair of terminals like you suggest, it won't matter which pair. An amplifier will put out more power through a low-impedance sub than it will through a high-impedance sub. Most all of them do, in fact, recommend precisely the placement you have adopted.
6 Ways to Install a Multiple Component Car Audio System - wikiHow
Subwoofer Wiring Diagrams How to Wire Your Subs
Kenneth, I'd leave your subs wired the way they are. If that lack of power is not an issue, you can wire them together like this. This is by far the most dangerous aspect of any high-end car audio system, dating sims games free as it can literally ruin equipment if not properly installed. Hopefully this makes sense and thank you!
- Over the last few years, I've also carved out a niche producing demo videos for our in-dash car stereos.
- Caleb, You're definitely confusing issues by quoting max ratings which are meaningless.
- If you want a question answered about a system, you must identify the gear by brand name and model number.
- What do you recommend on wiring?
- Another option is a dedicated crossover, but these can be tricky to work with, and quite expensive.
- It seems the mono's are cheaper.